Published Sep 13. 2021 - 1 month ago
Updated or edited Sep 14. 2021

Rattle.Bum Popper

Dron Lee from Malaysia has created this excellent little popper using a combination of foam and braided tube - and a rattle for some extra noise

Finished poppers and some underway
Finished poppers and some underway
Dron Lee

I get a lot of fly tying ideas from the various social media, and one of the really inventive and exciting tyers to follow is Malaysian Dron Lee.
Dron ties all kinds of flies, but tends to use new and different techniques and often gets some really nice and easy flies as a result.
This popper is a good example.

When I bumped into it as a step-by-step on Dron’s Facebook wall it didn’t have a name yet, but thanks to a bunch of suggestions from Dron’s Facbook friends, it wound up being called the Rattle.Bum Popper. That particular name was originated by Stephen Bussell, another Facebook user.
Like many of Dron’s flies it incorporates foam. It utilizes the foam for flotation, some braided tubing to form a body and eyes and flash and yarn fibers to make a tail. This makes it a perfect little colorful fish frantically escaping in the surface, making bubbles and noise thanks to its cupped front. It will also go zigging and zagging each time it’s stripped in, and as an added attractor Dron as mounted a rattler in the rear of the fly, yielding an even noisier fly. You can see it in action in the video below. It's a great fly for bass and other fish that react to some surface commotion.

Not small, not large
Not small, not large
Dron Lee

The base material for the fly is 5mm foam with a fused surface. This type of foam is often used for packaging and is mostly white, but can also be found in various colors – or be dyed with a waterproof marker. It’s folded over to form an oval cylinder, and cut in the shape shown in the pictures, which has an angle in the rear forming the base for tail, and a cup in the front creating the popping action. It can be hollowed in the front using a cauterizer. Dron also adds a small hole for the rattler, which is glued in place in the rear.

Foam and rattlers
Foam and rattlers
Dron Lee
Sidelines
Sidelines
Dron Lee

Two strips cut from a luminous, pearly sheet are glued in place on each side of the foam, which is then put into a piece of braided tubing at least twice the length of the foam. You can fuse the tube back and front using heat to form the body shape seen in the images. At this stage you can also have at it using waterproof markers to give the body a darker back or maybe some lateral stripes – or even both.

Braided tube
Braided tube
Dron Lee
Coloring
Coloring
Dron Lee

The body is then covered with a clear fabric glue that dries up clear and soft. Dron uses a type called F-6000, which is widely available and inexpensive. The glue fuses the braid to the foam and forms a nice surface.

Glueing
Gluing
Dron Lee
Drying
Drying
Dron Lee

Once the glue is dry, Dron trims the braid off in the front of the fly to expose the cup in the foam, and then pokes a hole for the hook using a large needle. The hook shank should be covered with a tight and rough layer of tying thread before it’s mounted. This will make the glue bind better. The eye passes through the braid from behind and the hook shank is epoxied in place. Also add some epoxy to the rear underside of the fly where the hook comes out for increased stability and durability. You can add the eyes using a dab of epoxy while it’s out anyway. Let the epoxy cure.

Trimming
Trimming
Dron Lee
Hole for the hook
Hole for the hook
Dron Lee
Hole done
Hole done
Dron Lee
Thread base
Thread base
Dron Lee
Gluing the hook shank
Gluing hook shank
Dron Lee
Ready to slide over
Ready to slide over
Dron Lee
Securing hook
Securing hook
Dron Lee
Hook in place
Hook in place
Dron Lee

Finally the tail is added by fraying up some polyyarn and using its fibers together with some flash – either a bunch of single straws or some flash chenille. Simply tie in or wrap a tuft of both and trim it to a suitable shape. Varnish or glue the wraps after whip finishing and cutting the thread.

Starting tail
Starting tail
Dron Lee
Adding fibers
Adding fibers
Dron Lee

When everything is dried and cured, your popper is ready to fish.

The finished fly
The finished fly
Dron Lee
Materials
Materials
Dron Lee
Rattle.Bum Popper
Pattern type: 
Bass bug
Originator: 
Dron Lee
Materials: 
Foam body
5 mm fused surface or closed cell foam in a color of your choice
Glue for body
Superglue
Rattle
Plastic rattle
Sidelines
Strips of pearl luminous sheet
Outer body
Braided tubing, app 1 cm Ø
Glue for braid
F-6000 fabric glue
Hook
Ahrex SA270 3/0
Thread
Semperfli waxed thread 6/0
Glue for hook and eyes
Epoxy
Eyes
4D living eye, app 3-4 mm Ø
Tail
Polyyarn and Palmer chenille or flash straws
Difficulty: 
Medium
Instruction: 
See article for detailed instructions

Back to the article top.

.

Log in or register to pre-fill name on comments, add videos, user pictures and more.
Read more about why you should register.
 

Since you got this far …


The GFF money box

… I have a small favor to ask.

Long story short

Support the Global FlyFisher through several different channels, including PayPal.

Long story longer

The Global FlyFisher has been online since the mid-90's and has been free to access for everybody since day one – and will stay free for as long as I run it.
But that doesn't mean that it's free to run.
It costs money to drive a large site like this.

See more details about what you can do to help in this blog post.